Motorcycle
Motorcycle

Installation Instructions

 11-200 Sportboard, R1150RT

Tools Required:

Small screwdriver, pliers, 3/8" wrench (1/8" Allen wrench, supplied in Parts Kit).

Parts Kit, Included:

2 Ea. 5/16" X 1 3/4" Clevis Pin

2 Ea. Cotter Pin

1 Ea. 1/8" Allen Wrench

1 Ea. Special Toe Tab

Place motorcycle on center stand.

Remove Stock Foot Pegs:

1. With screw driver and pliers, straighten and remove cotter pin.

2. Wiggle foot peg up and down as you remove the clevis pin. The foot peg is under some spring pressure, be careful as you pull out the pin.

3. Save all stock parts, never throw away original parts.

Install Sportboard:

1. Check to see that neither of the two ¼-20 nylon tipped setscrews are protruding from backside of mounting bracket.

2. Fit mounting bracket into clevis on footrest plate and install clevis pin. At this point the Sportboard will have some back and forth movement.

3. Orient clevis pin so that the cotter pin hole is facing rearwards. It will be easier to install the cotter pin after adjusting the setscrews in the mounting bracket.

4. Using the supplied 1/8" Allen wrench, tighten the two setscrews evenly to take out any play and align the Sportboard parallel to the motorcycle. Tighten each setscrew firmly and evenly with fingers only. Do not use pliers or a cheater on the Allen wrench.

5. Insert the end of the cotter pin into the clevis pin and push forward until it seats into position. Bend legs around clevis pin.

6. Check to make sure that the brake and shift levers are fully functional and that the side and center stand are unimpeded.

7. Check the Sportboards to insure that everything is tight and functioning properly.

Install Center Stand Bracket:

1. Remove the three nylok nuts and the top plate. (top plate detail 1) 

 detail1

 2. Install the bottom plate in the center stand. (detail 2)

detail2

3. Put top plate on and install the three nylok nuts (detail 3)

detail3

 

Search Products

Ilium Works is proud to announce the 29-200 HIGHWAY PEGS for the R1250 GS Adventure.

The factory engine guard bar configuration has presented quite a challenge when it comes to properly mounting a comfortable highway peg. Our new part number 29-200 Highway Pegs address this problem with a unique mounting system. A gracefully curved 1/4" X 1” stainless steel bar connects the upper and lower bars of the factory engine guard and provides a sturdy foundation to mount the highway pegs in the proper location.

The 29-300 GSA Highway peg is offered with the Gripper pad.

Carefully designed Rear Crash Bars to help protect your expensive panniers and mufflers, these minimalist design bars will not interfere with passenger comfort or the clean lines of your R1200RT Oil head, R1200RT Water Cooled, R1250RT or K1600GT / GTL / GTLE.These Rear Guard Bars, Part# 11-800BL are designed to work in conjunction with our P/N 19-600 Highway Pegs to offer the best overall protection for your 2005 – 2013 R1200RT in the event of a drop or tip over. These can also be used in conjunction with other manufacturer’s engine guard...

These Rear Guard Bars, Part# 30-800 / 30-800BL are designed to work in conjunction with our P/N 30-200 / 30-200BL (R1200RTW) or 36-200 / 36-200BL (R1250RT) Engine Guard Bars to offer the best overall protection for your R1200RT WATER COOLED or R1250RT in the event of a drop or tip over.  These can also be used in conjunction with other manufacturer’s engine guard bars as well.  These bars are constructed of heavy wall  (1” X .120” ) steel tubing and TIG welded to 7 ga. cold rolled steel brackets.  After shot blasting with stainless steel media, th...

Powered By Zomix Content Management Systems copyright © 2024